OASIS® BIOLINE® Heart Sophia, 50 x 48 x 5 cm

The mini vacuum suction cup made of transparent plastic was specially developed for products with the Easy-Click system: It is used to fix flower arrangements with OASIS® ECObase® hearts and the OASIS® ECObase® cross to smooth surfaces such as glass, mirrors, gravestones or car hoods (for vehicles with standard car paint).Attaching the vacuum suction cup to the products:Press the suction cup into the receptacle (plastic-lined recess in the hard foam base of the above-mentioned products) until it snaps into place. The round thickening at the top of the suction cup prevents the suction cup from detaching from the foam base.Fixing the arrangement to the intended base:Please first clean and dry the suction surface of the vacuum suction cup and the intended base. These must be clean, dry and free of grease, otherwise the holding power of the vacuum suction cup cannot be guaranteed. For example, freshly polished car paint can impair the holding power of the vacuum suction cup. In this case, the polish should be carefully removed from the corresponding area with warm water, detergent and a lint-free cloth.Removing the arrangement from the base:Use your fingertip to lift the suction surface of the vacuum cup slightly at the edge and allow air to flow into the existing vacuum. The vacuum suction cup will now detach from the base and the arrangement can be removed.

For particularly large room decorations and ideal for funeral floristry thanks to the natural wood base. The natural wood base gives the heart a high level of stability.TIP: After watering, the heart should be placed upright for approx. 30 minutes, as a water loss of up to 20% cannot be avoided.Ensure correct watering:Due to the size of the product, the conventional soaking method (placing the product foam-side down on the water and allowing it to soak up by itself) is unlikely to be used.A mortar mixing tub (available from DIY stores) is best suited as a watering vessel. It should also be clean and the water level in the container should be as high as possible. Water the heart by holding it vertically and slowly dipping it deep into the tub, heart tip first, until the bottom half of the heart is soaked with water. Then turn the heart over and water the top half in the same way.

Optimal for wedding floristry as a car decoration holder. The natural wood base gives the heart a high level of stability, and the vacuum suction cups can be attached quickly and easily using the holders on the back of the heart. This allows the heart to be easily attached to all smooth surfaces (e.g. car hood).Please note:The suction surface and the base (e.g. car hood) must be clean, dry and free of grease. Freshly polished car paint can reduce the suction cup's holding power, so the polish should be carefully removed from the relevant areas with warm water, washing-up liquid and a lint-free cloth.The attachment can be easily removed later if you lift the suction cup's plate with your fingertip at the edge so that air can flow into the vacuum. This allows the suction cup to be easily detached from the base.Make sure to water properly:Due to the size of the product, the conventional watering method (placing the product on the water with the foam side facing down and allowing it to soak up by itself) is rarely used.A mortar mixing tub (available from DIY stores) is best suited as a watering vessel. It should also be clean and the water level in the container should be as high as possible. Water the heart by holding it vertically and slowly dipping it deep into the tub, heart tip first, until the bottom half of the heart is soaked with water. Then turn the heart over and water the upper half in the same way.After watering, the heart should be placed upright for approx. 30 minutes, as a water loss of approx. 20 % cannot be avoided.

Optimal for wedding floristry as a car decoration holder.Please note:The suction surface and the base (e.g. car hood) must be clean, dry and free of grease. Freshly polished car paint can reduce the suction cup's holding power, so the polish should be carefully removed from the relevant areas with warm water, washing-up liquid and a lint-free cloth.The attachment can be easily removed later if you lift the suction cup's plate at the edge with your fingertip so that air can flow into the vacuum. This allows the suction cup to be easily detached from the base.Ensure correct watering:Due to the size of the product, the conventional watering method (place the product on the water with the foam side down and allow it to soak up by itself) is unlikely to be used.A mortar mixing tub (available from DIY stores) is best suited as a watering vessel. It should also be clean and the water level in the container should be as high as possible. Water the heart by holding it vertically and slowly dipping it deep into the tub with the tip of the heart first, until the lower half of the heart has been soaked with water. Then turn the heart over and water the top half in the same way.After watering, the heart should be placed upright for approx. 30 minutes, as a water loss of approx. 20% cannot be avoided.

Optimal for wedding floristry as a car decoration holder. The natural wood base gives the heart a high level of stability, and the vacuum suction cups can be attached quickly and easily using the holders on the back of the heart. This allows the heart to be easily attached to all smooth surfaces (e.g. car hood).Please note:The suction surface and the base (e.g. car hood) must be clean, dry and free of grease. Freshly polished car paint can reduce the suction cup's holding power, so the polish should be carefully removed from the relevant areas with warm water, washing-up liquid and a lint-free cloth.The attachment can be easily removed later if you lift the suction cup's plate with your fingertip at the edge so that air can flow into the vacuum. This allows the suction cup to be easily detached from the base.Ensure correct watering:Due to the size of the product, the conventional soaking method (placing the product on the water with the foam side down and allowing it to soak up by itself) is unlikely to be used. A mortar mixing tub (available from DIY stores) is best suited as a watering vessel. It should also be clean and the water level in the container should be as high as possible. Water the heart by holding it vertically and slowly dipping it deep into the tub, heart tip first, until the lower half of the heart is soaked with water. Then turn the heart over and water the top half in the same way After soaking, the heart should be placed upright for approx. 30 minutes, as a water loss of approx. 20 % cannot be avoided.